Just as white blood cells protect us from disease, similarly your gutters protect your roof from disaster. Gutters and downspots attached to your roof are the two most important, but most overlooked, areas of the home. Unfortunately, if none of these are properly installed or damaged, you will be left with a very high repair bill.
Also, the cost of installing the gutter is not cheap. As always, one way to eliminate many of these costs is to install the gutters themselves. This is quite a complex project, but one that many homeowners can do.
While gutter installation can be done by yourself, if you do not have the right equipment or knowledge, it is best to leave it to the professionals. Contact a Tyler Tx Roofing Pro today and get free quotes from contractors near you.
Which gutter to buy
Before starting such a project, you need to know how much material to purchase. Before you go to the store, go outside and measure the outside of your roof. You will need this number because it will help you in choosing the best material for your roof. According to our gutter cost calculator, the average price to install a gutter is $ 827.
Typically, gutters are sold in prefabricated lengths of 5, 10 or 15 feet. Downspots are also available in a variety of sizes to best suit your roof.
Homeowners usually choose metal for their gutters. The most suitable are galvanized steel and aluminum. They are excellent against rain, snow, and hail. Better yet, they can cost as little as $ 7 for 10 feet of material.
Some homeowners, on the other hand, prefer vinyl and / or copper. Both are very long-lasting and stronger than metal. But be careful, each section can cost up to five times.
How to install drain
The following steps should be followed to install aluminum gutters.
Measurement
- Measure the distance required for each drain.
- Measure the trim panel or fascia, which is located behind the groove.
- Be sure to measure the entire circumference of your roof before purchasing the material.
- Keep in mind that you will need several pieces in each corner.
- Be sure to purchase gutters for a long time to go around the entire roof. You will probably need to cut a few pieces for the ends and corners.
Prepare gutters
- Moving on to your gutter, you will need to install the end cap first. In this way, water will reduce your flow and not the other way around. You can buy a mouthpiece in the store.
- Add some sealant to the end cap and gently hold it against the drain.
- You can also use small nails or crimping pliers for extra strength.
- Measure the length of your first gutter and cut if necessary. The store can recommend the best cutting tool based on the material chosen.
- Take your word and keep both together, but do not tie them together. Ensure that the lengths of both gutters match the desired length. The length should not be correct as the gutter expands and shrinks due to weather conditions.
- Insert a few tails inside the corner gutters and press the two together.
- Use a power drill and drill a few small holes to connect the two pieces together. You can use small nails or rivets, mainly used to join two pieces of metal together.
Next, we need a larger hole for the downspout. - Drill a large hole in the groove or down the drain. Some people prefer to use saw holes.
- Put an exit or metal fence in the hole with putty and rivets.
Connect fascia to fascia
- Hold the groove where you want it and make sure it fits properly.
- Before laying the gutters completely, make sure that the gutters have a staircase or a slope to ensure that the water is flowing down.
- Also, make sure that the drain is slightly below the ceiling. A small drop should fall from the roof to the drain.
- First, connect the top end of the gutter or the bottom of the gutter to the bottom.
- Calculate for the bottom of the fascia from one end to another end.
- Go to the other end of the drain. Ensure that the distance from the underside of the fascia is shorter (half an inch) than the other side. Now you know that the water will flow downstream.
- Use your drain mounting bracket and long nails to attach the drain to the house or rafters.
- You should notice any nails or dent on the dashboard. Install your braces just above these protrusions.
Connect down
- Attach the elbow joints to the parts connecting the drain and downspout. You can use a little caul or rivets to help.
- Some homeowners add brackets to the bottom to ensure that they are flush with the wall.
- Ensure that the downspout is not facing the base.
- Just to be on the safe side, place a PVC pipe at the end of your down spot. In this way, the water will flow further from the house.
Installing your own gutter can save you up to $ 800. However, keep in mind that your gutters can have a major impact on the life of your roof. If you are uncomfortable with this type of job, I highly recommend calling the gutter repair and installation Tyler, Tx near you.
